router ENHWI-3GN3 print

The Encore ENHWI-3GN3 router has 300mbps WiFi, 2 100mbps ETH-ports and 0 USB-ports.

Quick links:
Default password/Login
User Manuals

ENHWI-3GN3 router specifications (specs)

System specs
Cpu: 320 MHz
RAM: n/a
Flash: n/a
Custom firmwares: OpenWrt
Connectivity
WiFi: 300mbps (bgn)
WAN-ports: 1
WAN-speed: 100mbps (10/100)
ETH-ports (LAN): 2
ETH-speed: 100mbps (10/100)
USB-ports: 0

Hard reset instructions for Encore ENHWI-3GN3

If your ENHWI-3GN3 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your Encore ENHWI-3GN3 in the following way(s):

The 30-30-30 reset

There are no specific instructions for this model yet, but you can always do the 30-30-30 reset as follows:
  1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
  2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
  3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting. If that doesn't work be sure to check out the questions and answers incase someone else has had similar problems resetting their router.
Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.

Default factory settings for Encore ENHWI-3GN3

If you have performed a reset of your ENHWI-3GN3 device or not changed the defaults, you should be able to access it with the following settings:

Default Network name (SSID): ENCOREXXXXXX
Default Gateway IP: 192.168.0.1 Encore login instructions
Default username: admin Encore router default password list
Default password: admin 
Default subnet mask: 255.255.255.0
Default DNS server: 192.168.0.1
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

User Manuals for ENHWI-3GN3

Do you still have questions concerning the router that you can't find online? You can always try the manuals where most questions should be answered from the manufacturer. Below are the device manuals available for your ENHWI-3GN3.

Name Type Size Date
save Manual Part 1 (click to download) pdf 1.61 MB July 20, 2009
save Manual Part 2 (click to download) pdf 2.45 MB July 20, 2009
save Manual (click to download) pdf 3.48 MB Jan. 23, 2009

ENHWI-3GN3 Firmwares

Staying up to date with the latest firmware is a good idea to keep your router even more secure from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Encore ENHWI-3GN3:

Flashing OpenWrt on the Encore ENHWI-3GN3

The Encore ENHWI-3GN3 is supported by OpenWrt according to their Table of Hardware. So flashing OpenWrt onto it should be quite straigthforward.
We couldn't find any specific instructions for flashin OpenWrt on the Encore ENHWI-3GN3, but since it's listed in their Table of Hardware as supported, you can head over to the OpenWrt install instructions and read on there.
Note: Flashing custom firmwares is always on you're on own risk. Make sure to read OpenWrt's wikis to understand the risks and how to proceed if something goes wrong.

Encore stock firmware for the ENHWI-3GN3

Stock firmwares for the ENHWI-3GN3 are available under the download section on the modem's support page. You can also refer to the router's manual for instructions on how to upgrade the firmware.