router R7000 print Nighthawk AC1900 Smart WiFi Router
R7000 router specifications (specs)
CPU: 1 GHz
RAM: 256 MiB
Flash: 128 MiB
Custom firmwares: OpenWrt
WiFi: Gigabit (abgn+ac)
WiFi bands: 2.4GHz & 5GHz
WiFi throughput: n/a
WAN: 1 Gigabit port
ETH: 4 Gigabit ports
Hard reset instructions for Netgear R7000
If your R7000 router is not working as it should, dropping connections or not being
responsive, you should first do a reset of the router to see if the problems persist. Other
scenarios where you might want to reset your router is if you've forgotten the password or
misconfigured it and can't get access anymore.
Your can reset your Netgear R7000 in the following way(s):
With the reset button
- Have the router powered on (if just booted wait around one minute for it to load)
- With a sharp pen or paper clip, press down the Restore Factory Settings button and hold it for about 7 seconds
- When the power light starts to blink you can release the reset button and wait for the router to start up
- The power light will be solid (not blinking) once the router is started.
The 30-30-30 resetIf the above instructions don't work you can always try the 30-30-30 reset as follows:
- When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
- While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
- While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.
This process usually works for resetting any router to it's factory setting.
If that doesn't work be sure to check out the
questions and answers
incase someone else has had similar problems resetting their router.
Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.
Default factory settings for Netgear R7000
If you have performed a reset of your R7000 device or not changed the defaults, you should be able to access it with the following settings:
Default password: password
Default subnet mask: 255.255.255.0
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.
User Manuals for R7000
Do you still have questions concerning the router that you can't find online? You can always try the manuals where most questions should be answered from the manufacturer. Below are the device manuals available for your R7000.
|save User Manual Part 2 (click to download)||2.04 MB||May 12, 2015|
|save User Manual (click to download)||2.51 MB||Aug. 6, 2013|
|save User Manual Part 1 (click to download)||4.9 MB||May 12, 2015|
Staying up to date with the latest firmware is a good idea to keep your router even more secure
from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Netgear R7000:
Flashing OpenWrt on the Netgear R7000
The Netgear R7000 is supported by OpenWrt according to their Table of Hardware. So
flashing OpenWrt onto it should be quite straigthforward.
We couldn't find any specific instructions for flashin OpenWrt on the Netgear R7000, but since it's listed in their Table of Hardware as supported, you can head over to the OpenWrt install instructions and read on there.
Note: Flashing custom firmwares is always on you're on own risk. Make sure to read OpenWrt's wikis to understand the risks and how to proceed if something goes wrong.
Netgear stock firmware for the R7000
Stock firmwares for the R7000 are available under the download section on the modem's support page. You can also refer to the router's manual for instructions on how to upgrade the firmware.