router WNDAP350 print

The Netgear WNDAP350 router has 300mbps WiFi, 1 Gigabit ETH-ports and 0 USB-ports.

Quick links:
Default password/Login
User Manuals

WNDAP350 router specifications (specs)

System specs
Cpu: 680 MHz
RAM: 128 MiB
Flash: 8 MiB
Custom firmwares: None
Connectivity
WiFi: 300mbps (abgn)
WiFi bands: 2.4GHz & 5GHz
WAN: None
ETH: 1 Gigabit port
USB-ports: 0

Hard reset instructions for Netgear WNDAP350

If your WNDAP350 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your Netgear WNDAP350 in the following way(s):

With the reset button

  1. Have the router powered on (if just booted wait around one minute for it to load)
  2. With a sharp pen or paper clip, press down the Restore Factory Settings button and hold it for about 7 seconds
  3. When the power light starts to blink you can release the reset button and wait for the router to start up
  4. The power light will be solid (not blinking) once the router is started.

The 30-30-30 reset

If the above instructions don't work you can always try the 30-30-30 reset as follows:
  1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
  2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
  3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting. If that doesn't work be sure to check out the questions and answers incase someone else has had similar problems resetting their router.
Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.

Default factory settings for Netgear WNDAP350

If you have performed a reset of your WNDAP350 device or not changed the defaults, you should be able to access it with the following settings:

Default Network name (SSID): NETGEAR_11g,NETGEAR_11a
Default Gateway IP: 192.168.0.237 Netgear login instructions
Default username: admin Netgear router default password list
Default password: password 
Default subnet mask: 255.255.255.0
Default DNS server: 192.168.0.237
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

User Manuals for WNDAP350

Do you still have questions concerning the router that you can't find online? You can always try the manuals where most questions should be answered from the manufacturer. Below are the device manuals available for your WNDAP350.

Name Type Size Date
save Users Manual (statement).pdf (click to download) pdf 7.03 kB Sept. 17, 2015
save Users Manual.pdf (click to download) pdf 2.19 MB Sept. 17, 2015
save User Manual (click to download) pdf 2.61 MB Nov. 2, 2009

WNDAP350 Firmwares

Staying up to date with the latest firmware is a good idea to keep your router even more secure from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Netgear WNDAP350:

Netgear stock firmware for the WNDAP350

Stock firmwares for the WNDAP350 are available under the download section on the modem's support page. You can also refer to the router's manual for instructions on how to upgrade the firmware.