NanoStation Loco M2

The Ubiquiti Networks NanoStation Loco M2 router has 300mbps WiFi, 1 100mbps ETH-ports and 0 USB-ports.

Quick links:
Default password/Login
Login instructions
User Manuals


NanoStation Loco M2 router specifications (specs)

System specs
CPU: 400 MHz
RAM: 32 MiB
Flash: 8 MiB
Custom firmwares: OpenWrt
Connectivity
WiFi: 300mbps (bgn)
WiFi bands: 2.4GHz
WiFi throughput: n/a
WAN: None
ETH: 1 x 100mbps port
USB-ports: 0

Ubiquiti Networks NanoStation Loco M2 review (quick overview)

Here is the quick comparison of how the Ubiquiti Networks NanoStation Loco M2 compares to other routers on our site:

Average 35/100
Editor 90/100
WiFi 6/100
Hardware 9/100
Current price $139.94

For a full list of routers and how they compare to the NanoStation Loco M2, check the Router Buying Guide which will help you buy the most price-competitive router.

Hard reset instructions for Ubiquiti Networks NanoStation Loco M2

If your NanoStation Loco M2 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your Ubiquiti Networks NanoStation Loco M2 in the following way(s):

The 30-30-30 reset

There are no specific instructions for this model yet, but you can always do the 30-30-30 reset as follows:
  1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
  2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
  3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting. If that doesn't work be sure to check out the questions and answers incase someone else has had similar problems resetting their router.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.


Default factory settings for Ubiquiti Networks NanoStation Loco M2

If you have performed a reset of your NanoStation Loco M2 device or not changed the defaults, you should be able to access it with the following settings:

Default Network name (SSID): ubnt
Default Gateway IP: 192.168.1.20 Ubiquiti Networks login instructions
Default username: ubnt Ubiquiti Networks router default password list
Default password: ubnt 
Default subnet mask: 255.255.255.0
Default DNS server: 192.168.1.20
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

How to login to the NanoStation Loco M2

To login to the NanoStation Loco M2 router and change the settings, you can follow these steps:

  1. Make sure you are connected to the router's network, either by Wi-Fi or ethernet cable.
  2. Open your browser and visit http://192.168.1.20
  3. You should be prompted with a login dialogue.
  4. Enter the username: ubnt and the password ubnt
    Note: If you have already changed the password use that instead.
  5. You will now be logged in. If you haven't yet changed the defaul password, we recommend that you change it first thing you do after logging in.

If these instructions don't work for your router, you can always try a factory reset to get the default, or try some other common Ubiquiti Networks credentials, as they can usually be shared across models/variants.




Report error on page
(If info is incorrect)