NWA1123-NI v1 print

Router info

OpenWrt supported: no
dd-wrt supported: no
RAM: 64 MiB
WiFi: 300mbps (abgn)
WAN-speed: N/A ()
ETH-ports (LAN): 1
ETH-speed: Gigabit (10/100/1000)
USB-ports: 0
Other versions (newest first):
  • NWA1123-NI v2 (2014)
  • Hard reset instructions for ZyXEL NWA1123-NI v1

    If your NWA1123-NI v1 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
    Your can reset your ZyXEL NWA1123-NI v1 in the following way(s):

    Through web interface

    1. Open web browser and go to the address of your router (check defaults below)
    2. Log in with your username/password (default are below)
    3. Under Maintenance, locate Backup/Restore and click it
    4. Locate the section Factory defaults and click the reset button, if prompted click Ok
    5. Wait for the router to reboot

    With the reset button

    1. Have the router plugged in and turned on
    2. Locate the reset button which is marked reset and usually in a hole
    3. With a paperclip or sharp pen, press and hold the reset button for 10 seconds until the SYS light starts to blink
      1. If the SYS light doesn't start to blink after 10 seconds:
        1. Keep holding the reset button pressed
        2. Turn off the modem / unplug it
        3. While still holding the reset button, start / plug in the router
        4. After about 20 seconds, the Power or SYS light will start blinking rapidly
        5. Release the reset button
    4. When the light stops blinking and light up normally the router is reset.

    The 30-30-30 reset

    If the above instructions don't work you can always try the 30-30-30 reset as follows:
    1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
    2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
    3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

    This process usually works for resetting any router to it's factory setting. If that doesn't work be sure to check out the questions and answers incase someone else has had similar problems resetting their router.
    Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.

    Default factory settings for ZyXEL NWA1123-NI v1

    If you have performed a reset of your NWA1123-NI v1 device or not changed the defaults, you should be able to access it with the following settings:

    Default Gateway IP:
    Default admin username: admin
    Default admin password: 1234
    Default subnet mask:
    Default DNS server:
    Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

    User Manuals for NWA1123-NI v1

    Do you still have questions concerning the router that you can't find online? You can always try the manuals where most questions should be answered from the manufacturer. Below are the device manuals available for your NWA1123-NI v1.

    Name Type Size Date
    save User Manual.pdf (click to download) pdf 4.63 MB June 18, 2014
    save User Man_I88NWA1123NI_rev (click to download) pdf 4.75 MB Jan. 3, 2013
    Cookies disclaimer

    I agree Our site saves small pieces of text information (cookies) on your device in order to deliver better content and for statistical purposes. You can disable the usage of cookies by changing the settings of your browser. By browsing our website without changing the browser settings you grant us permission to store that information on your device.