WHR-G125

The Buffalo WHR-G125 router has 54mbps WiFi, 4 100mbps ETH-ports and 0 USB-ports. It also supports custom firmwares like: dd-wrt, OpenWrt

Quick links:
Default password/Login
Login instructions
User Manuals
Flashing Custom Firmwares


WHR-G125 router specifications (specs)

System specs
CPU: 240 MHz
RAM: 16 MiB
Flash: 4 MiB
Custom firmwares: dd-wrt, OpenWrt
Connectivity
WiFi: 54mbps (bg)
WiFi bands: 2.4GHz
WiFi throughput: n/a
WAN: 1 x 100mbps port
ETH: 4 x 100mbps ports
USB-ports: 0

Hard reset instructions for Buffalo WHR-G125

If your WHR-G125 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your Buffalo WHR-G125 in the following way(s):

The 30-30-30 reset

There are no specific instructions for this model yet, but you can always do the 30-30-30 reset as follows:
  1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
  2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
  3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.


Default factory settings for Buffalo WHR-G125

If you have performed a reset of your WHR-G125 device or not changed the defaults, you should be able to access it with the following settings:

Default Network name (SSID): XYXYXYXYXYXYXYXYXYXYXYXY
Default Gateway IP: 192.168.11.1 Buffalo login instructions
Default username: root Buffalo router default password list
Default subnet mask: 255.255.255.0
Default DNS server: 192.168.11.1
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

How to login to the WHR-G125

To login to the WHR-G125 router and change the settings, you can follow these steps:

  1. Make sure you are connected to the router's network, either by Wi-Fi or ethernet cable.
  2. Open your browser and visit http://192.168.11.1
  3. You should be prompted with a login dialogue.
  4. Enter the username: root and if it requires a password, leave it empty or try with admin/password
    Note: If you have already changed the password use that instead.
  5. You will now be logged in. If you haven't yet changed the defaul password, we recommend that you change it first thing you do after logging in.

If these instructions don't work for your router, you can always try a factory reset to get the default, or try some other common Buffalo credentials, as they can usually be shared across models/variants.


WHR-G125 Firmwares

Staying up to date with the latest firmware is a good idea to keep your router even more secure from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Buffalo WHR-G125:

Flashing dd-wrt on the Buffalo WHR-G125

Since the WHR-G125 has 4 MiB of flash memory, you should choose a stripped down version of dd-wrt that fits on the smaller flash. We haven't find any specific instructions for flashin dd-wrt onto the Buffalo WHR-G125, but you can read the Installation guide over at dd-wrt to get a clue on how to proceed (As this model is listed as supported).
Note: Always make sure to read the wiki and howtos of dd-wrt before doing any flashing.

Flashing OpenWrt on the Buffalo WHR-G125

The Buffalo WHR-G125 is supported by OpenWrt according to their Table of Hardware. So flashing OpenWrt onto it should be quite straigthforward.
We couldn't find any specific instructions for flashin OpenWrt on the Buffalo WHR-G125, but since it's listed in their Table of Hardware as supported, you can head over to the OpenWrt install instructions and read on there.
Note: Flashing custom firmwares is always on you're on own risk. Make sure to read OpenWrt's wikis to understand the risks and how to proceed if something goes wrong.




Report error on page
(If info is incorrect)