FVS336Gv2
Netgear ProSafe Dual WAN Gigabit SSL VPN Firewall

The Netgear FVS336Gv2 router has No WiFi, 4 N/A ETH-ports and 0 USB-ports.
It is also known as the Netgear Netgear ProSafe Dual WAN Gigabit SSL VPN Firewall.

Quick links:
Default password/Login
Login instructions



FVS336Gv2 router specifications (specs)

System specs
CPU: 300 MHz
RAM: 128 MiB
Flash: 32 MiB
Custom firmwares: None
Connectivity
WiFi: No ()
WiFi bands: n/a
WiFi throughput: n/a
WAN: 2 x N/A ports
ETH: 4 x N/A ports
USB-ports: 0

Hard reset instructions for Netgear FVS336Gv2

If your FVS336Gv2 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your Netgear FVS336Gv2 in the following way(s):

With the reset button

  1. Have the router powered on (if just booted wait around one minute for it to load)
  2. With a sharp pen or paper clip, press down the Restore Factory Settings button and hold it for about 7 seconds
  3. When the power light starts to blink you can release the reset button and wait for the router to start up
  4. The power light will be solid (not blinking) once the router is started.

The 30-30-30 reset

If the above instructions don't work you can always try the 30-30-30 reset as follows:
  1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
  2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
  3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.


Default factory settings for Netgear FVS336Gv2

If you have performed a reset of your FVS336Gv2 device or not changed the defaults, you should be able to access it with the following settings:

Default Gateway IP: 192.168.1.1 Netgear login instructions
Default username: admin Netgear router default password list
Default password: password 
Default subnet mask: 255.255.255.0
Default DNS server: 192.168.1.1
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

How to login to the FVS336Gv2

To login to the Netgear ProSafe Dual WAN Gigabit SSL VPN Firewall and change the settings, you can follow these steps:

  1. Make sure you are connected to the router's network, either by Wi-Fi or ethernet cable.
  2. Open your browser and visit http://192.168.1.1
  3. You should be prompted with a login dialogue.
  4. Enter the username: admin and the password password
    Note: If you have already changed the password use that instead.
  5. You will now be logged in. If you haven't yet changed the defaul password, we recommend that you change it first thing you do after logging in.

If these instructions don't work for your router, you can always try a factory reset to get the default, or try some other common Netgear credentials, as they can usually be shared across models/variants.




Report error on page
(If info is incorrect)