WLR-9500
AC2600 High Coverage MU-MIMO Wi-Fi Router

The Sitecom WLR-9500 router has Gigabit WiFi, 4 Gigabit ETH-ports and 0 USB-ports.
It is also known as the Sitecom AC2600 High Coverage MU-MIMO Wi-Fi Router.

Quick links:
Default password/Login
Login instructions


WLR-9500 router specifications (specs)

System specs
CPU: 1 GHz
RAM: 128 MiB
Flash: 16 MiB
Custom firmwares: None
Connectivity
WiFi: Gigabit (abgn+ac)
WiFi bands: n/a
WiFi throughput: n/a
WAN: 1 x Gigabit port
ETH: 4 x Gigabit ports
USB-ports: 0

Hard reset instructions for Sitecom WLR-9500

If your WLR-9500 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your Sitecom WLR-9500 in the following way(s):

The 30-30-30 reset

There are no specific instructions for this model yet, but you can always do the 30-30-30 reset as follows:
  1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
  2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
  3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.


Default factory settings for Sitecom WLR-9500

If you have performed a reset of your WLR-9500 device or not changed the defaults, you should be able to access it with the following settings:

Default Gateway IP: 192.168.0.1 Sitecom login instructions
Default username: admin Sitecom router default password list
Default subnet mask: 255.255.255.0
Default DNS server: 192.168.0.1
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

How to login to the WLR-9500

To login to the AC2600 High Coverage MU-MIMO Wi-Fi Router and change the settings, you can follow these steps:

  1. Make sure you are connected to the router's network, either by Wi-Fi or ethernet cable.
  2. Open your browser and visit http://192.168.0.1
  3. You should be prompted with a login dialogue.
  4. Enter the username: admin and if it requires a password, leave it empty or try with admin/password
    Note: If you have already changed the password use that instead.
  5. You will now be logged in. If you haven't yet changed the defaul password, we recommend that you change it first thing you do after logging in.

If these instructions don't work for your router, you can always try a factory reset to get the default, or try some other common Sitecom credentials, as they can usually be shared across models/variants.


WLR-9500 Firmwares

Staying up to date with the latest firmware is a good idea to keep your router even more secure from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Sitecom WLR-9500:

Sitecom stock firmware for the WLR-9500

Stock firmwares for the WLR-9500 are available under the download section on the modem's support page. You can also refer to the router's manual for instructions on how to upgrade the firmware.




Report error on page
(If info is incorrect)