ENHWI-2AN3
802.11n Wireless N300 Router / Repeater / Access Point: 3-in-1

The Encore ENHWI-2AN3 router has 300mbps WiFi, 4 100mbps ETH-ports and 0 USB-ports.
It's also known as the Encore 802.11n Wireless N300 Router / Repeater / Access Point: 3-in-1. It also supports custom firmwares like: dd-wrt, OpenWrt.

Quick links:
Default password/Login
User Manuals
Flashing Custom Firmwares


ENHWI-2AN3 router specifications (specs)

System specs
CPU: 384 MHz
RAM: 32 MiB
Flash: 4 MiB
Custom firmwares: dd-wrt, OpenWrt
Connectivity
WiFi: 300mbps (bgn)
WiFi bands: 2.4GHz
WiFi throughput: n/a
WAN: 1 x 100mbps port
ETH: 4 x 100mbps ports
USB-ports: 0

Hard reset instructions for Encore ENHWI-2AN3

If your ENHWI-2AN3 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your Encore ENHWI-2AN3 in the following way(s):

The 30-30-30 reset

There are no specific instructions for this model yet, but you can always do the 30-30-30 reset as follows:
  1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
  2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
  3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting. If that doesn't work be sure to check out the questions and answers incase someone else has had similar problems resetting their router.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.


Default factory settings for Encore ENHWI-2AN3

If you have performed a reset of your ENHWI-2AN3 device or not changed the defaults, you should be able to access it with the following settings:

Default Network name (SSID): ENCOREXXXXXX
Default Gateway IP: 192.168.0.1 Encore login instructions
Default username: admin Encore router default password list
Default password: admin 
Default subnet mask: 255.255.255.0
Default DNS server: 192.168.0.1
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

User Manuals for ENHWI-2AN3

Do you still have questions concerning the router that you can't find online? You can always try the manuals where most questions should be answered from the manufacturer. Below are the device manuals available for your ENHWI-2AN3.

Name Type Size Date
Manual (click to download) pdf 1.99 MB Oct. 9, 2008

ENHWI-2AN3 Firmwares

Staying up to date with the latest firmware is a good idea to keep your router even more secure from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Encore ENHWI-2AN3:

Flashing dd-wrt on the Encore ENHWI-2AN3

Since the ENHWI-2AN3 has 4 MiB of flash memory, you should choose a stripped down version of dd-wrt that fits on the smaller flash. We haven't find any specific instructions for flashin dd-wrt onto the Encore ENHWI-2AN3, but you can read the Installation guide over at dd-wrt to get a clue on how to proceed (As this model is listed as supported).
Note: Always make sure to read the wiki and howtos of dd-wrt before doing any flashing.

Flashing OpenWrt on the Encore ENHWI-2AN3

The Encore ENHWI-2AN3 is supported by OpenWrt according to their Table of Hardware. So flashing OpenWrt onto it should be quite straigthforward.
We couldn't find any specific instructions for flashin OpenWrt on the Encore ENHWI-2AN3, but since it's listed in their Table of Hardware as supported, you can head over to the OpenWrt install instructions and read on there.
Note: Flashing custom firmwares is always on you're on own risk. Make sure to read OpenWrt's wikis to understand the risks and how to proceed if something goes wrong.

Encore stock firmware for the ENHWI-2AN3

Stock firmwares for the ENHWI-2AN3 are available under the download section on the modem's support page. You can also refer to the router's manual for instructions on how to upgrade the firmware.




Report error on page
(If info is incorrect)