Meraki MX60W

The Cisco Meraki MX60W router has 300mbps WiFi, 4 Gigabit ETH-ports and 0 USB-ports. It also supports custom firmwares like: OpenWrt, LEDE Project

Quick links:
Default password/Login
User Manuals
Flashing Custom Firmwares


Meraki MX60W router specifications (specs)

System specs
CPU: 800 MHz
RAM: 512 MiB
Flash: 1024 MiB
Custom firmwares: OpenWrt, LEDE Project
Connectivity
WiFi: 300mbps (abgn)
WiFi bands: 2.4GHz & 5GHz
WiFi throughput: n/a
WAN: 1 x Gigabit port
ETH: 4 x Gigabit ports
USB-ports: 0

Hard reset instructions for Cisco Meraki MX60W

If your Meraki MX60W router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your Cisco Meraki MX60W in the following way(s):

The 30-30-30 reset

There are no specific instructions for this model yet, but you can always do the 30-30-30 reset as follows:
  1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
  2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
  3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.


Default factory settings for Cisco Meraki MX60W

If you have performed a reset of your Meraki MX60W device or not changed the defaults, you should be able to access it with the following settings:

Default subnet mask: 255.255.255.0

Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

User Manuals for Meraki MX60W

Do you still have questions concerning the router that you can't find online? You can always try the manuals where most questions should be answered from the manufacturer. Below are the device manuals available for your Meraki MX60W.

Name Type Size Date
User Manual (click to download) pdf 27.34 kB April 13, 2012

Meraki MX60W Firmwares

Staying up to date with the latest firmware is a good idea to keep your router even more secure from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Cisco Meraki MX60W:

Flashing OpenWrt on the Cisco Meraki MX60W

The Cisco Meraki MX60W is supported by OpenWrt according to their Table of Hardware. So flashing OpenWrt onto it should be quite straigthforward.
We couldn't find any specific instructions for flashin OpenWrt on the Cisco Meraki MX60W, but since it's listed in their Table of Hardware as supported, you can head over to the OpenWrt install instructions and read on there.
Note: Flashing custom firmwares is always on you're on own risk. Make sure to read OpenWrt's wikis to understand the risks and how to proceed if something goes wrong.

Flashing LEDE Project on the Meraki MX60W

The Cisco Meraki MX60W is also supported by the LEDE Project.
To install LEDE aquire the correct firmware from their Firmware downloads page and then follow the instructions on their Quick Start Guide
Note: Make sure to read the LEDE wikis carefully before flashing.




Report error on page
(If info is incorrect)