DWL-8620APE rev A1
Wireless AC2600 Wave2 4x4 MU-MIMO Dual Band Unified Access Point

The D-Link DWL-8620APE rev A1 router has Gigabit WiFi, 2 N/A ETH-ports and 0 USB-ports. It has a total combined WiFi throughput of 2600 Mpbs.
It is also known as the D-Link Wireless AC2600 Wave2 4x4 MU-MIMO Dual Band Unified Access Point.

Quick links:
Default password/Login
Login instructions



DWL-8620APE rev A1 router specifications (specs)

System specs
CPU: 1.4 GHz
RAM: 512 MiB
Flash: 128 MiB
Custom firmwares: None
Connectivity
WiFi: Gigabit (abgn+ac)
WiFi bands: 2.4GHz & 5GHz
WiFi throughput: 2600 Mpbs
WAN: None
ETH: 2 x N/A ports
USB-ports: 0

Hard reset instructions for D-Link DWL-8620APE rev A1

If your DWL-8620APE rev A1 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your D-Link DWL-8620APE rev A1 in the following way(s):

With the reset button

  1. Locate the reset button on the back off the router
  2. While the unit is powered on, press the reset button with a sharp object (e.g. paperclip)
  3. Hold the button pressed for 10 seconds, then release.
  4. The unit will reboot by itself and once the WLAN light stops blinking the factory reset is done.
  5. You can now setup your router again through the user interface

The 30-30-30 reset

If the above instructions don't work you can always try the 30-30-30 reset as follows:
  1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
  2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
  3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.


Default factory settings for D-Link DWL-8620APE rev A1

If you have performed a reset of your DWL-8620APE rev A1 device or not changed the defaults, you should be able to access it with the following settings:

Default Gateway IP: 10.90.90.91 D-Link login instructions
Default username: admin D-Link router default password list
Default password: admin 
Default subnet mask: 255.255.255.0
Default DNS server: 10.90.90.91
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

How to login to the DWL-8620APE rev A1

To login to the Wireless AC2600 Wave2 4x4 MU-MIMO Dual Band Unified Access Point and change the settings, you can follow these steps:

  1. Make sure you are connected to the router's network, either by Wi-Fi or ethernet cable.
  2. Open your browser and visit http://10.90.90.91
  3. You should be prompted with a login dialogue.
  4. Enter the username: admin and the password admin
    Note: If you have already changed the password use that instead.
  5. You will now be logged in. If you haven't yet changed the defaul password, we recommend that you change it first thing you do after logging in.

If these instructions don't work for your router, you can always try a factory reset to get the default, or try some other common D-Link credentials, as they can usually be shared across models/variants.




Report error on page
(If info is incorrect)