E4200 v1
Maximum Performance Dual-Band N Router

The Linksys E4200 v1 router has 300mbps WiFi, 4 N/A ETH-ports and 0 USB-ports.
It is also known as the Linksys Maximum Performance Dual-Band N Router.It also supports custom firmwares like: dd-wrt, OpenWrt

Quick links:
Default password/Login
User Manuals
Flashing Custom Firmwares



E4200 v1 router specifications (specs)

System specs
CPU: 480 MHz
RAM: 64 MiB
Flash: 16 MiB
Custom firmwares: dd-wrt, OpenWrt
Connectivity
WiFi: 300mbps (abgn)
WiFi bands: 2.4GHz & 5GHz
WiFi throughput: n/a
WAN: 1 x N/A port
ETH: 4 x N/A ports
USB-ports: 0

Linksys E4200 review (quick overview)

Here is the quick comparison of how the Linksys E4200 compares to other routers on our site:

Average 34/100
Editor 84/100
WiFi 6/100
Hardware 12/100
Current price Find best price

For a full list of routers and how they compare to the E4200 v1, check the Router Buying Guide which will help you buy the most price-competitive router.

Hard reset instructions for Linksys E4200 v1

If your E4200 v1 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your Linksys E4200 v1 in the following way(s):

Through the web interface

  1. Open your browser and navigate to the router interface (check default settings below)
  2. Under the Administration tab you will find a sub-tab called Factory defaults
  3. On the Factory defaults page click the button labeled Restore Factory Defaults

With the reset button

  1. Have your unit powered on
  2. Press and hold the reset button for at least 10 seconds until the power light starts blinking, then release.
  3. When the power light goes solid, unplug the power to the router for 10 seconds
  4. Plug the power back in and start the router
  5. When the power light goes solid again the router is ready to use.

The 30-30-30 reset

If the above instructions don't work you can always try the 30-30-30 reset as follows:
  1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
  2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
  3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting. If that doesn't work be sure to check out the questions and answers incase someone else has had similar problems resetting their router.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.


Default factory settings for Linksys E4200 v1

If you have performed a reset of your E4200 v1 device or not changed the defaults, you should be able to access it with the following settings:

Default Network name (SSID): CiscoXYXYXYXX
Default Gateway IP: 192.168.1.1 Linksys login instructions
Default password: admin 
Default subnet mask: 255.255.255.0
Default DNS server: 192.168.1.1
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

E4200 v1 Firmwares

Staying up to date with the latest firmware is a good idea to keep your router even more secure from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Linksys E4200 v1:

Flashing dd-wrt on the Linksys E4200 v1

Since the E4200 v1 has 16 MiB of flash memory, you should be able to run dd-wrt with full functionality without having to worry too much about which firmware to use.
Instructions on how to flash dd-wrt onto your Linksys E4200 v1 can be found on the dd-wrt wiki
Note: Always make sure to read the wiki and howtos of dd-wrt before doing any flashing.

Flashing OpenWrt on the Linksys E4200 v1

The Linksys E4200 v1 is supported by OpenWrt according to their Table of Hardware. So flashing OpenWrt onto it should be quite straigthforward.
To get started with the flashing, head over to the OpenWrt instructions for E4200 v1 and they'll take it from there.
Note: Flashing custom firmwares is always on you're on own risk. Make sure to read OpenWrt's wikis to understand the risks and how to proceed if something goes wrong.

Linksys stock firmware for the E4200 v1

Stock firmwares for the E4200 v1 are available under the download section on the modem's support page. You can also refer to the router's manual for instructions on how to upgrade the firmware.




Report error on page
(If info is incorrect)