WES610N v1
Dual-Band N Entertainment Bridge with 4-Port Switch

The Linksys WES610N v1 router has 300mbps WiFi, 4 100mbps ETH-ports and 0 USB-ports.
It's also known as the Linksys Dual-Band N Entertainment Bridge with 4-Port Switch.

Quick links:
Default password/Login
User Manuals



WES610N v1 router specifications (specs)

System specs
CPU: 200 MHz
RAM: 32 MiB
Flash: 4 MiB
Custom firmwares: None
Connectivity
WiFi: 300mbps (abgn)
WiFi bands: 2.4GHz & 5GHz
WiFi throughput: n/a
WAN: None
ETH: 4 x 100mbps ports
USB-ports: 0

Hard reset instructions for Linksys WES610N v1

If your WES610N v1 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your Linksys WES610N v1 in the following way(s):

Through the web interface

  1. Open your browser and navigate to the router interface (check default settings below)
  2. Under the Administration tab you will find a sub-tab called Factory defaults
  3. On the Factory defaults page click the button labeled Restore Factory Defaults

With the reset button

  1. Have your unit powered on
  2. Press and hold the reset button for at least 10 seconds until the power light starts blinking, then release.
  3. When the power light goes solid, unplug the power to the router for 10 seconds
  4. Plug the power back in and start the router
  5. When the power light goes solid again the router is ready to use.

The 30-30-30 reset

If the above instructions don't work you can always try the 30-30-30 reset as follows:
  1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
  2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
  3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting. If that doesn't work be sure to check out the questions and answers incase someone else has had similar problems resetting their router.

Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.


Default factory settings for Linksys WES610N v1

If you have performed a reset of your WES610N v1 device or not changed the defaults, you should be able to access it with the following settings:

Default Gateway IP: 169.254.1.250 Linksys login instructions
Default password: admin 
Default subnet mask: 255.255.255.0
Default DNS server: 169.254.1.250
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

User Manuals for WES610N v1

Do you still have questions concerning the router that you can't find online? You can always try the manuals where most questions should be answered from the manufacturer. Below are the device manuals available for your WES610N v1.

Name Type Size Date
User Manual (click to download) pdf 2.2 MB March 31, 2011

WES610N v1 Firmwares

Staying up to date with the latest firmware is a good idea to keep your router even more secure from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Linksys WES610N v1:

Linksys stock firmware for the WES610N v1

Stock firmwares for the WES610N v1 are available under the download section on the modem's support page. You can also refer to the router's manual for instructions on how to upgrade the firmware.




Report error on page
(If info is incorrect)